EIGRP頻寬例項配置
EIGRP路由資訊在預設情況下佔用介面頻寬的50%,而序列介面預設的頻寬為T1(1.544M),但在實際上序列介面的頻寬並不是預設值,這裡我們按照需求修改介面的頻寬並修改EIGRP 佔用頻寬的百分比例。拓撲圖如下:
修改頻寬佔用比:
R1(config)# interface s0/0
R1(config-if)# bandwidth 128 //注意,這裡的單位是KB/s
R1(config-if)# ip bandwidth-percent eigrp 100 40 //修改EIGRP 路由資訊佔用頻寬的百分比為40
R1(config-if)# end
R2(config)# interface s0/0
R2(config-if)# bandwidth 64 //注意,這裡的單位是KB/s
R2(config-if)# end
R3(config)# interface s0/0
R3(config-if)# bandwidth 64 //注意,這裡的單位是KB/s
R3(config-if)# end
驗證:
R1#show interfaces seriAL 0/0 | include BW
MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
EIGRP 在幀中繼網路中使用點對點子介面的方式。第4 步配置中,可以看到R2 和R3 想要通過R1 學習到對方宣告的網路,必須將R1 的介面S0/0 水平分割關閉才可以。這裡我們使用幀中繼網路點對點子介面的.方法來完成。
點對點子介面方式:
R1(config)#default interface Serial 0/0 //將介面的配置還原為預設值
Building configuration…
Interface Serial0/0 set to default configuration
R1(config)#
*Mar 1 01:45:30.363: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor (Serial0/0) is resync: split horizon changed
*Mar 1 01:45:30.367: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor (Serial0/0) is resync: split horizon changed
*Mar 1 01:45:30.779: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor (Serial0/0) is down: interface down
*Mar 1 01:45:30.787: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor (Serial0/0) is down: interface down
*Mar 1 01:45:31.483: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down
*Mar 1 01:45:33.499: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up
R1(config)#interface Serial 0/0
R1(config-if)#encapsulation fram //封裝為幀中繼模式
R1(config-if)#no fram inv //關閉自動獲取
R1(config-if)#no sh
R1(config-if)#ip split eigrp 100 //開啟水平分割
R1(config-if)#int s0/0.1 point //設定點對點子介面
R1(config-subif)#ip add
R1(config-subif)#fram interface-dlci 102 //指定介面DLCI 號
R1(config-fr-dlci)#int s0/0.2 point //配置R1 和R3 之間的子介面
R1(config-subif)#ip add
R1(config-subif)#fram interface-dlci 103
*Mar 1 01:47:05.767: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor (Serial0/0.1) is up: new adjacency
*Mar 1 01:47:06.651: IP-EIGRP(Default-IP-Routing-Table:100): Neighbor not on common subnet for Serial0/0.2
R1(config-fr-dlci)#end
因為R1 和R2 相連的子介面IP 地址和子網掩碼有所變化必須修改
R2(config)#int s0/0
R2(config-if)#ip add
因為R1 和R3 相連的子介面IP 地址和子網掩碼有所變化必須修改
R3(config)#int s0/0
R3(config-if)#ip add
*Mar 1 01:47:51.331: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor (Serial0/0) is down: address changed
*Mar 1 01:47:51.343: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor (Serial0/0) is down: address changed
*Mar 1 01:47:52.463: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 100: Neighbor (Serial0/0) is up: new adjacency
R3(config-if)#no frame-relay map ip 301 broadcas //將之前配置的取消
R3(config-if)#fram map ip 301 br
驗證配置:
R1#show ip eigrp neighbors
IP-EIGRP neighbors for process 100
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
1 Se0/0.2 173 00:06:53 117 1053 0 15
0 Se0/0.1 135 00:07:12 1055 5000 0 16
R3#ping
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 20/89/180 ms
-
如何檢視電腦無線網路密碼
有時候時間久了很容易忘記電腦的無線網路密碼,也就是Wifi密碼,當朋友或者家人無線裝置需要無線上網的時候,就要告知其密碼,那麼如何檢視電腦無線網路密碼?下面是小編為大家帶來的'如何檢視電腦無線網路密碼的知識,歡迎閱讀。方法一:直接檢視電腦無線密碼1、點選桌面...
-
2017網路技術考試題「附答案」
一、選擇題1在有互連的開放系統中,位於同一層上的系統構成了OSI的(B)層。A物理B對等C傳輸D網路2FDM是按照(A)的差別來分割訊號的。A頻率參量B時間參量C碼型結構DA、B、C均不是3線路交換不具有的優點是(A)A傳輸時延小B處理開銷小C對資料資訊格式和編碼型別沒有限...
-
實用執行命令功能詳解
你是不是羨慕一些高手能夠熟練的使用鍵盤快捷鍵與各種命令,從容的玩轉著電腦。其實,不用羨慕,因為很多快捷鍵或者命令操作也都很簡單,下面,小編給大家介紹10個實用的執行命令,讓你也能體驗一把電腦高手的感覺!要使用命令操作,最基本的是先需要如何開啟執行操作框,主要...
-
雲路由器設定後無法上網怎麼辦
雲路由器設定後無法上網怎麼辦?以下是YJBYS小編搜尋整理的相關內容,供參考閱讀,希望對大家有所幫助!想了解更多相關資訊請持續關注我們應屆畢業生培訓網!雲路由器設定後無法上網,請點選網路狀態,如下:觀察網路狀態區域的提示資訊,如下:請參考對應提示的處理方法:頁面提...